Explorez tous les épisodes du podcast Power Driven Podcast
| Titre | Date | Durée | |
|---|---|---|---|
| Building A 6.4 Cummins: The RIGHT Way vs The WRONG Way! | 17 nov. 2026 | 00:35:40 | |
What actually makes a Cummins stroker, and why does “6.4” mean two completely different engines? Todd, Will, and Myer break down how stroker engines are built, what they gain you, and how to do one on your own truck. If you’ve ever wondered what a 6.1 or 6.4 Cummins really is, this episode clears it up. Dropping a 6.7 crank into a 5.9 gets you a 6.1, and a 40 over 5.9 with that same crank gets you a 6.2. The 6.4 is where people get confused. One version is the old short stroke combo with a 5.9 crank in a 6.7 block. The other, and now the more common, is a sleeved down 6.7 that keeps the full 6.7 stroke, like Myer’s engine, which adds cylinder wall thickness for strength. For the 12 valve guys, they walk through a 12v Cummins build step by step. The 6.7 crank bolts right in because rod length, main journals, and deck height all match, but you’ll need to swap the straight cut crank gear. Decking about 80 thousandths off the pistons bumps compression a point or more. That means better spool, more torque, and better fuel economy, as long as you stay under what the block can handle. Common rail owners aren’t left out. They cover why bowl and injector placement matter on a 5.9 common rail, the 80 thousandths shorter Wagler rods made for this exact swap, and why higher piston protrusion helps a 6.7 tow build. They also talk about how injector washer thickness on a 12 valve changes nozzle depth in the bowl, a trick that used to be worth around 25 horsepower on the dyno. Before getting into engines, the guys tackle a viewer comment from Rusty Water 3219 about Gale Banks saying black diesel smoke is unburned fuel that melts pistons. They explain why that’s fair for a loaded street truck pulling a grade, but misleading when you’re chasing peak power. In recent turbo testing on a small single, the truck made around 680 horsepower tuned nearly clean. Adding fuel until it ran dark gray at roughly .86 lambda pushed it to about 850 on the same turbo. They also compare diesel tuning to high end gas engines, which make peak power in a surprisingly similar lambda range. So when someone says diesel guys don’t know how to tune, the smoke is really just how a diesel burns fuel when air is the limit. If you want it clean and mean, that’s where nitrous comes in. And for the record, unburned fuel isn’t black. Black smoke is partially burned fuel, kind of like burnt toast. If you’re into Cummins builds and real diesel tuning talk, subscribe on YouTube and follow the Power Driven Podcast wherever you listen. Let us know if you want more engine episodes. If you’re planning a stroker build of your own, Power Driven has the 6.7 cranks with the helical gear already on them, plus the blocks, rods, and parts the guys talk about in this episode. Shop everything mentioned at PowerDriven.com, links below. Shop Power Driven Diesel: https://www.powerdriven.com ⚙️Power Driven True 6.7 Cummins Crankshaft: https://powerdriven.com/products/power-driven-true-6-7-cummins-crankshaft 🚚New 6.7L Cummins OEM Engine Block: https://powerdriven.com/products/new-6-7l-cummins-oem-engine-block-07-5-18 🛠️Street Fighter Connecting Rods 0.080" Shorter (6.1L Stroker Kits): https://powerdriven.com/products/street-fighter-connecting-rods-0-080-shorter-for-6-1l-stroker-kits 🔧Wagler Street Fighter Connecting Rods: https://powerdriven.com/products/wagler-crd5-9-6-7st-street-fighter-connecting-rods-for-89-18-cummins-5-9-6-7l-up-to-1500-hp 🔥Power Driven 12v Cummins Injector Shim Kit: https://powerdriven.com/products/power-driven-12v-cummins-injector-shim-kit | |||
| Your 2019+ Cummins Is a Ticking Time Bomb (Here’s the Fix) | 10 nov. 2026 | 01:19:09 | |
If you own a 2019 through 2026 Ram 2500 or 3500 with the 6.7 Cummins, you’ve probably heard the lifter failure horror stories and wondered if your fifth gen is a ticking time bomb. This episode breaks down exactly why these engines fail and what you can actually do about it before that typewriter tick turns into a full engine teardown. Todd, Will, and Myer walk through what changed on the 5th gen Cummins in 2019 and why. Stellantis wanted a lighter engine, a cheaper maintenance schedule, and a quieter truck. So Cummins went to a compacted graphite iron block, full cam bushings, a steel roller cam, and self adjusting hydraulic roller lifters. It still says 6.7 Cummins on the side, but under the valve cover it’s a very different engine than the 4th gen. The guys explain how that design leads to pushrod and rocker arm wear, bent pushrods, lifter slack, and eventually wiped cam lobes. They also bust a couple of common myths. The factory lifter does not have needle bearings, and that little key on the side of the lifter is not a guide pin. Using insight from a Cummins engineer, they cover the real failure modes, the Ram TSB on lifter tick, the undersized oil feed passage, dry starts, and the 10W30 versus 15W40 oil debate. Then they get into the fix. Power Driven and Colt Cams are releasing a flat tappet conversion kit that puts proven 1989 to 2018 Cummins valvetrain technology back in your fifth gen. It comes with cast tappets, upgraded 7/16 pushrods, adjustable rocker arms, and a smooth street and towing camshaft. They talk about how hard the install is, the cam options (including a stock replacement grind for strict emissions states), and why this setup opens the door to performance cams for guys chasing more diesel performance. Will has been working on this fix for a couple of years, and it’s a big part of why Power Driven brought Colt Cams in house. Before the fifth gen talk, they answer listener questions:
If you learned something, subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or wherever you listen. Drop your questions in the comments, because the guys really do read them. If your fifth gen is ticking or you want to get ahead of lifter failure, the Colt Cams 6.7 Cummins Flat Tappet Reliability Kit puts proven flat tappet technology back in your 2019 to 2024 Ram. You can pick the Tow Series 181/210 or the Street Series 181/218 cam. Shop everything mentioned in this episode at PowerDriven.com: links below. Shop Power Driven Diesel: https://www.powerdriven.com Colt Cams 2019 to 2024 6.7L Cummins Flat Tappet Reliability Kit: https://coltcams.com/products/2019-2024-6-7-cummins-flat-tappet-reliability-kit | |||
| How to Run NITROUS on a CUMMINS Without Blowing It Up! | 03 nov. 2026 | 01:29:13 | |
Nitrous will make power your turbos alone never will, and it will scatter a diesel engine just as fast if you set it up wrong. This episode is the full nitrous strategy, from your first bottle on a single turbo truck to the tuning behind 4,000 horsepower Cummins dyno hits. Todd, Will, and Myer start with nitrous oxide basics: what is in the bottle, why the extra oxygen makes so much power, and why a single eighth inch solenoid tops out around 250 horsepower. They get into where to spray it, why pre intercooler is the safest spot on a turbo diesel, and how bottle pressure, line size, and phase change decide how much nitrous actually reaches the engine. If three stages of spray only picked up 100 horsepower on your truck, the answer is probably in your plumbing. Next up is using nitrous to spool a big turbocharger on the line. The guys explain why a 52 jet is a safe place to start, why too much spray makes a diesel pop, backfire, or snuff out, and how a Hobbs switch, full throttle switch, or pulse width controller keeps it under control. Then it gets into wastegates, which might be the biggest part of the whole deal. Nitrous makes a ton of exhaust energy and will overspeed a single turbo in a hurry, so they walk through setting up a gate with regulated boost to the hat and keeping your fuel only power when the bottle runs dry. You will also hear how gates and spray took boost to 144 pounds while drive pressure actually dropped on a compound turbo setup. The diesel tuning side is where most motors get saved or lost. They cover how clean your truck should be before you ever spray it, why timing has to change when you pull fuel, how to read EGT if you do not have a dyno, and why a two second hit beats a ten second hero run. Plus the story of a 12 valve that went down the drag strip close to 70 to 1 air fuel, and why everything you learned from gas guys goes out the window on a diesel. They also kick off a new comment section segment with a viewer question: does a 250 amp high output alternator hurt horsepower or fuel economy? If you are into diesel performance, diesel drag racing, or building faster diesel trucks, subscribe on YouTube and follow the Power Driven Podcast on your favorite platform. Drop your nitrous questions in the comments and we might answer them on the show. Shop nitrous kits, controllers, wastegates, and everything else mentioned in this episode at PowerDriven.com. Links below. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Why Diesel Experts Make MORE POWER Than You! | 27 oct. 2026 | 00:53:08 | |
Ever heard someone swear a big diesel dyno number has to be fake? On this episode of the Power Driven Podcast, Todd, Will, and Myer take on the dyno slap myth and get into what really separates the guys making serious diesel horsepower from everybody else. Spoiler: it’s not cheating, it’s obsession. The guys break down why certain people become the go to experts on one Cummins platform, whether that’s a first gen, a VP44 2nd gen Cummins, or a P pump 12 valve Cummins. Seat time on one diesel engine teaches you things no forum post ever will, like a VP44 builder finding real horsepower differences just by swapping ECMs. You’ll also hear a great 12 valve troubleshooting story from a recent event. A 1995 Dodge Cummins lost its tach and speedometer, and after 40 minutes with a wiring diagram, the culprit turned out to be a pulled fuel pump fuse in the PDC. On a 95, that fuse also feeds the PCM, so pulling it to “delete” a lift pump that was never there killed the computer. Then the crew gets into diesel dyno strategy and why dyno slapping isn’t real. Myer explains how his Cummins nitrous kits are staged about 200 rpm apart with fuel ramping in over roughly 1,000 rpm. He opens the wastegates ahead of the spray to keep boost and drive pressure in check, and repeatable dyno runs that line up with the math prove the numbers are legit. They also cover how overfueling a big turbo diesel setup cools the exhaust and snuffs the turbo, and how to set up an AFC on a hot 12 valve so it doesn’t hit full fuel too early. Myer’s 48RE transmission has been a big part of his season at the Ultimate Callout Challenge (UCC), diesel drag racing events, and dyno days. As far as the crew knows, it’s holding more power than anyone has put through a Turbo 400, and the only maintenance on the truck all year has been an oil change. They explain how transmission slip can scatter an engine and why a Bosch ECM that thinks fast enough is worth every dollar over a factory 849. You’ll also hear why a 6.4 deck plate isn’t automatically the right call over a 6.7, why common rail diesel trucks dominate turbo limited classes like 72 fast, and the small details that win dyno days: chains instead of loose straps, rear lockouts, a spool, a weight rack, and where the tire sits on the roller. To wrap it up, a listener writes in to settle the EGT versus EGTs debate once and for all. If you’re into Cummins builds, diesel performance, diesel tuning, and making real horsepower, subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or wherever you listen. Whether you’re chasing your first 1,000 horsepower out of a P pump 12 valve or building a Cummins that can survive serious dyno abuse, the parts and know-how behind this episode are available at PowerDriven.com. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Single Turbo vs Compounds: Which ACTUALLY Makes More Power? | 20 oct. 2026 | 00:54:59 | |
Single turbo or compound turbo: which one really makes more horsepower? This episode started with a comment from viewer @V8Lenny (youtube.com/@V8Lenny) claiming a single turbo will always make more power than the same charger run in compounds, so we put that claim up against years of diesel dyno numbers and real Cummins builds. The conversation starts with results from 12 valve Cummins and 6.7 Cummins common rail diesel trucks. A 98mm charger that made 1100 horsepower as a single made 1500 to 1600 in a compound setup, while an S480 made the same power either way. It also covers why big singles are so hard to tune on a common rail diesel, from snuffing the turbo with too much fuel to adjusting rail pressure and timing so the fuel drives the charger. From there it gets into turbo science. Diesels have less drive energy than gas engines, which is why sled pull turbos run huge turbine wheels and why high altitude makes everything harder. Compressor efficiency, pulse energy, and interstage cooling all come into play, along with The Godfather, a triple turbo 12 valve that made 2800 horsepower with four stages of densification. Cylinder head flow is a big part of the picture too. Head flow decides where an engine wants to make peak power, and matching your turbos to the head matters more than chasing RPM. Testing on the Junker drag truck shows both sides of the single turbo vs twin turbo debate: an S476 single that barely broke 700 on a 5.9 Cummins, an S369 single that beat a set of towing compounds, and a 12v Cummins build where compounds made way more power. The episode also explains why compounds spool better at low RPM and when they don’t. It wraps with the 72 Fast class pushing near 1500 horsepower on a 72mm turbo and a final verdict on @V8Lenny (youtube.com/@V8Lenny) claim: compressor for compressor, a well tuned single usually wins, but compounds are way easier to tune. If you want real diesel power talk from guys who run this stuff on the dyno, subscribe to Power Driven Diesel on YouTube and follow the Power Driven Podcast wherever you listen. Building a big single or a set of compounds? Power Driven Diesel has the parts to back it up. Aggressor turbos, compound turbo systems, CNC ported cylinder heads, and complete power packages for 12 valve, 24 valve, and common rail Cummins are all available at PowerDriven.com. Shop Power Driven Diesel: https://powerdriven.com | |||
| The TRUTH About The VP44: Making 500HP On A BUDGET | 13 oct. 2026 | 00:40:21 | |
What happens when an $11,000 VP44 Cummins with a short parts list out tow trucks that cost five times as much? Willard, our 2001 Dodge Ram dually, just pulled a race trailer home from Diesels in the Mountains and held the speed limit up the grades. This episode breaks down why this old 24 valve keeps surprising everybody and what it takes to turn a 25 year old diesel truck into a legit cross country tow rig. Todd, Will, and Myer walk through the simple build on this 5.9 Cummins with the VP44 injection pump: a 650 horsepower transmission, Power Driven stage two injectors, a turbo upgrade, head studs, intake, and exhaust. On a clean tow tune it pulls hard, makes around 520 wheel horsepower on the top tune, and the EGT control is so good the crew had to verify the gauge with dual pyros on the dyno. They also get honest about the limitations, like the four speed and 3.55 gears making it slow off the line with a heavy trailer compared to a newer six speed truck. Next they cover the comfort list that turns a fun truck into a real tow truck. That means killing exhaust drone with a better tip and a big straight through muffler, adding an inline four inch exhaust brake that leaves room for compounds later, and why V band connections matter for exhaust brake performance. Old truck problems get their own fix list too: a leaking heater core, a cracked second gen dash, sound deadening while the interior is out, a turbo silencer ring, a modern radio with a backup camera, better tow mirrors, headlights, and brakes. The guys also run the numbers. Willard sits around $22,000 all in, with way fewer electrical gremlins than a brand new Ram 2500 that can lock you in the cab on the side of the highway. Finally, they map out the next stage of this VP44 build: camshaft, ported cylinder head, then turbos, chasing a 700 to 800 horsepower tow truck on a stock VP44 pump. Plus some fun talk about how Willard might stack up against the new 8.3L Duramax in a TFL Truck style towing test. If you love old Cummins trucks and real diesel performance talk, subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or wherever you listen. The parts that make Willard tow like this are the Power Driven stage two VP44 injectors, the 650 horsepower transmission, and the turbo setup. If your turbo whistle is wearing on you during long tows, the turbo silencer rings are on the site too. Shop everything mentioned in this episode at PowerDriven.com. Links below. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| This 6.7 Cummins Head Won $100,000 in Diesel Drag Racing | 06 oct. 2026 | 00:54:01 | |
A shelf on cylinder head just won the biggest payday in diesel drag racing, and it beat trucks running heads that flow a lot more air. If you think bigger is always better on a race build, this episode of the Power Driven Podcast might make you rethink your whole combo. Todd, Will, and Myer break down the 72 Fast class in Texas, where first place took home $100,000. Every truck runs the same 72mm VS Racing turbo with zero modifications, weighs at least 6,000 pounds, keeps a factory ECM, and launches off a foot brake against an instant green tree. No nitrous, no water injection, no trans brake. It all comes down to engine building, tuning, and the guy behind the wheel. Will explains how he ran the numbers on Matthew Parker's 6.7 Cummins and built him a Power Driven Stage 3 diesel cylinder head with the shelf left on. At a 4,000 rpm shift point, the engine only needed about 267 CFM, and the head flowed 261 on the bench. Parker tested it back to back against his old head with the same tune, watched his air fuel ratio go leaner, kept adding fuel, and eventually ran out of CP3 at peak torque. He went on to win Texas after already taking Indy. The guys also talk about Spencer Shultz, who finished runner up with a head Will reworked after a dyno contest, and why those two trucks were nearly dead even. That opens up a straightforward breakdown of coefficient of discharge, valve size, and airspeed, and why a smaller, efficient port can fill the cylinder better than a big one when everything is sized to your RPM window. Camshaft selection, two valve versus four valve heads, and why injector placement matters for combustion all come up too. It is the kind of conversation every diesel engine build should start with before anyone orders parts. To wrap things up, they cover rumored new classes for next season, plans for their own race trucks over the winter, and a 3,503 uncorrected horsepower pull on a SuperFlow dyno that set a record for raw numbers on that machine. If you are into diesel performance and truck drag racing, subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or wherever you listen. Plenty more coming this winter. The Power Driven Stage 3 cylinder head that carried Matthew Parker to his second straight 72 Fast win is available for your own 6.7 Cummins, along with our full lineup of diesel cylinder heads, engine blocks, and performance parts built and tested in house using real race data. Whether you are building a race truck or a street build that pulls harder where you actually drive it, grab everything mentioned in this episode at PowerDriven.com. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| What It Takes to Keep a Cummins Alive at 3,600 HP | 29 sept. 2026 | 01:02:29 | |
What does it actually take to keep a Cummins alive past 3,000 horsepower on the dyno? It is not just more fuel and a bigger nitrous shot. This episode breaks down the real engineering behind Myer's second gen common rail race truck and why so many mega power builds scatter before the pull is over. With Diesels in the Mountains coming up in Utah, Todd, Will, and Myer dig into the torque limit of a factory cast block and why it wants to split right at the cam tunnel. They explain how making the same torque at 6,000 rpm instead of 2,500 turns a tow rig number into a record number, and why dyno correction factor at altitude means the uncorrected number is the one worth comparing. On the engine side, the guys walk through how a deck plate and a longer rod move the peak cylinder pressure above the factory block, and why they run the sleeves with a loose fit instead of a press fit so the weaker cast iron is not preloaded before the fire ever happens. For diesel tuning, they cover why nitrous means pulling 10 to 15 degrees of timing compared to a fuel only tune, how injector size changes how precise your injection window has to be, and why floating valves are behind most nitrous dyno blowups. Diesel cylinder pressure at this level is closer to Top Fuel than anything a gas valve manufacturer is used to, which is why Inconel is on the table. Then it gets into the turbo and nitrous setup. Myer runs four bottles, each on its own feed line, plus three wastegates that open the moment each nitrous kit fires so boost stays in check before it can overshoot. They also talk about undivided turbine housings, running as lean as 50 to 1 on the dyno, and why four bottles is about delivery, not showing off. The episode wraps with transmission line pressure and how slippage quietly costs hundreds of horsepower, running higher tire pressure with a spool to keep tires from blowing apart, and the dream of a hub dyno power wheelie. If you learned something, subscribe on YouTube and follow the Power Driven Podcast on your favorite platform so you catch the next one. From deck plates and sleeves to turbo boots and nitrous components, the parts behind builds like Myer's are the same ones we run and trust every day. Shop everything mentioned in this episode at PowerDriven.com. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| We Tried Everything Stupid So You Don't Have To! | 22 sept. 2026 | 01:05:37 | |
Every diesel guy has a list of mods he would take back, and in this episode Todd, Will, and Myer own up to theirs. From pushrods that snapped on a tow to Texas to a 12 valve Cummins quietly running out of oil, this is a shop floor confession about diesel truck mistakes that cost real time and money, and how to avoid repeating them on your own build. They break down turbo choices that missed the mark in both directions, including a big single on a 12 valve that never wanted to spool, an oversized junkyard turbo that made a truck lazier, and why a smaller 60/64 setup on their VP44 test truck ended up being the most fun to drive and tow with. If you are picking a turbo for your Cummins, that lesson alone is worth the listen. The fuel side gets plenty of attention too. The guys talk about cheap lift pumps that fell flat feeding a VP44, why a 13mm injection pump with no timing advance felt underwhelming, and how delivery valves really work, including where a full cut helps and where it just adds smoke and EGT. Then the fabrication stories start. Doubled up flex plates, a home welded turbo adapter, splines welded onto an input shaft, injector nozzles that sprayed the wrong way in a 12 valve, and a gallery plug that needed overnight to cure all come with lessons learned the hard way. They also cover mods that look cool but bite back, like hood stacks that coat the cab in soot, ceramic clutches on a street truck, torque converters that are too tight or too loose, and duct tape and baling wire on a boost boot. Plus what they learned about cast compressor wheels overspeeding on the dyno, and why you keep the engine running after a turbo lets go. Got a dumb mod story of your own? Drop it in the comments. Subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or your favorite podcast app so you never miss an episode. This episode is full of hard lessons on turbos, lift pumps, delivery valves, and fabrication, and if you want to build it right the first time instead of learning it the hard way like these guys did, Power Driven Diesel has the parts and the know how to help. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Everything You're Doing WRONG Building a 1000HP Cummins! | 15 sept. 2026 | 00:52:50 | |
Todd, Will, and Myer sit down to build the ultimate 1000 horsepower Cummins street truck from the ground up, part by part. Five hundred horsepower used to be the number that turned heads. Now the bar has moved, and this episode lays out exactly what it takes to build a diesel truck that lives at four digits and still drives home every night. The guys pick a 2006 third gen Dodge with a 5.9 Cummins as the starting platform and spend real time weighing that against stepping up to a 6.7 Cummins, covering spool, towing manners, and how each block handles the power level. If you're deciding between a 5.9 and a 6.7 for your own diesel truck build, this breakdown will save you a lot of guessing. From there the conversation moves into turbos, comparing the factory 8351CW against aftermarket compound setups built around an S466, S467, and a 98 millimeter atmosphere charger. They talk through single turbo versus compound turbo tradeoffs, when a wastegate actually matters at this power level, and how compressor and turbine sizing changes spool and peak power on the dyno. They cover the bottom end and cylinder head next, going over street fighter connecting rods, 14 millimeter main studs, and the ongoing debate between H, P, and V bearings for a truck that sees real street miles. On top of the block, they break down cylinder head stages, valve springs, pushrods, and when a bigger intercooler actually becomes necessary as boost climbs. Fueling gets plenty of attention too, with a look at CP3 pumps, single versus dual injector setups in 12 and 14 millimeter sizes, lift pump options like Air Dog and Fleece, and why upgrading your rail pressure sensor and relief valve matters once you push past factory pressure. If you're serious about building a reliable 1000 horsepower diesel truck, hit subscribe on YouTube and follow the Power Driven Podcast on your favorite podcast app so you never miss an episode. Shop everything mentioned in this episode at PowerDriven.com. All month long you can save 10% off everything at Power Driven, 15% off PDD Fueling, 10% off Airdog, and 10% off OptiTorque. Every purchase this month also gets you five entries to September's giveaway: a compound turbo kit, a Colt Cams cam combo that includes a PDD cylinder head, an Aggressor turbo, a fuel package, and an Airdog fuel system. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Why High Performance Diesel Engines Actually Fail.. | 08 sept. 2026 | 01:07:41 | |
You want to build a fast diesel and you don't want to blow it up in the process. This episode is the one you need before you ever touch a tune. Todd, Will, and Myer sit down and go through every real reason a high performance diesel engine dies, and it's rarely what you'd expect from reading the forums. They start by busting the EGT myth. Guys have been scared of exhaust gas temperature for decades, but heat alone almost never kills a build. What actually wrecks pistons is improper piston wall clearance, something the diesel performance world has gotten wrong for years. They break down cast versus forged pistons, correct ring gap on 12 valve and 24 valve Cummins engines, and why a factory rod that survives a worn out truck making 600 horsepower will bend the moment you put real power to a fresh, tight engine. From there they get into nitrous and timing. Todd and Will walk through why running too much timing with a big nitrous shot on a common rail is a fast way to send cylinder pressure through the roof, why sled pulling with water injection wants more timing than drag racing with nitrous, and how a lot of the old "nitrous blew it up" stories were actually piston clearance problems the whole time. Tulip valves get their own deep dive. This is one of the biggest issues quietly taking out modern high performance heads, and the guys explain how cylinder pressure pushes the valve up, kills your lash, wipes cams, and why Power Driven is working with a manufacturer on Inconel valves built specifically for common rail engines. They also cover rod bolt failures from over revving on the dyno, why disconnecting lockup or overdrive at high RPM without load will scatter an engine every time, and why running without an exhaust brake can quietly kill factory rods on a long mountain coast down. They close out talking through where to set your RPM window on a build so you're not fighting factory block and head limitations before you even lay into the throttle. If you're turning up a diesel or building a race truck, hit subscribe on YouTube and follow along on your favorite podcast app so you don't miss the next one. September is a big one. Power Driven is running 10% off everything storewide, 15% off PDD Fueling, and 10% off both Airdog and OptiTorque. On top of that there are five giveaways running including a compound turbo kit, a Colt Cams cam combo with a PDD cylinder head, an Aggressor turbo, a full fuel package, and an Airdog fuel system. Get all of it at PowerDriven.com before the sale ends. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| What Actually KILLS a Diesel Engine? | 01 sept. 2026 | 01:07:02 | |
Todd, Will, and Myer sit down to answer the question their own viewers keep asking: what actually kills a diesel engine. This isn't a highlight reel of blown up race trucks. It's a real conversation about the boring stuff that ends up costing you the most, and by the end you'll understand exactly why some trucks hit 400,000 miles and others don't make it past 100,000. The guys start with air filtration, breaking down why a high flow filter built for the racetrack can be the wrong call for a truck that spends its life on dirt roads, and how a warped air box lid quietly sands down cylinder walls one mile at a time. From there they get into oil change intervals, why diesel oil has to fight abrasive soot, and why stretching that interval too far on a Cummins or any diesel truck build is gambling with the bottom end. Fuel system maintenance gets serious attention too. Todd and Myer walk through algae contamination, injector failures on common rail systems, and why a cheap tune from Facebook Marketplace can melt a piston faster than almost anything else on this list. They break down EGT damage, ring wear, and valve seat problems, then go platform by platform. You'll hear about killer dowel pin issues on 12 valve Cummins trucks, VP44 fuel pressure sensitivity, the notorious CP4 pump problems on 6.7 Power Stroke trucks, head gasket failures on Duramax engines, and why the fifth gen Cummins hydraulic roller cam setup has turned into one of the more frustrating design decisions in recent diesel history. Whether you're running a 5.9 Cummins, a 6.7 Cummins, a Power Stroke, or a Duramax, this episode gives you a real look at what wears these engines out and what you can actually do about it before it becomes an expensive lesson. If you're a diesel guy who wrenches on your own truck, this is the kind of episode worth taking notes on. Subscribe on YouTube and follow the Power Driven Podcast on your favorite podcast platform so you don't miss the next one. Shop everything talked about in this episode, including the filters, oil, and parts, at the link below. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Diesel Tuning 101: Everything You Need To Know | 25 août 2026 | 01:21:53 | |
Tuning is one of the most asked topics in the diesel world, so this episode of the Power Driven Podcast breaks down diesel tuning 101 straight from guys who actually tune their own trucks. Todd, Will, and Myer walk through what it really takes to start tuning a Dodge Cummins, whether it is a daily driver or a dedicated race truck. They start with picking the right tuning platform, comparing EFI Live and HP Tuners for older and newer trucks, and explain how that software reads the ECM and unlocks the tuning tables hiding inside the factory computer. From there the conversation moves into fuel quantity, timing splits, and how injection pressure differs between a 12 valve pump truck and a modern common rail Cummins, and why that difference changes how aggressively you can safely run your tables. The guys also get into the factory five position tune switch found on 06 and newer Dodge Cummins trucks, how racers use it to flip between tunes right from the cab, and how other diesel platforms like Ford handle the same idea through the cruise control buttons. There is a long section on turbo spool, boost limited fueling, and reading an AFR gauge to hit the right air fuel ratio for a fast, clean spool without drowning the truck in smoke. That leads into a story about chasing spool on a Cummins sled pull truck that turned into one of the better lessons in this episode, plus why a properly tuned diesel will always beat someone trying to manage boost and fuel with their foot. Whether you daily drive a Dodge Cummins or you are building out a diesel performance race truck, this episode gives you a real starting point for tuning your own truck instead of guessing at it and hoping for the best. If you want more episodes like this, subscribe to the Power Driven Podcast on YouTube and follow along on your favorite podcast platform. Shop everything mentioned in this episode at PowerDriven.com, including EFI Live and HP Tuners tuning platforms and gear to help you dial in your own Dodge Cummins. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Spectator Ride-Alongs: The Most Fun We've Had At A Race | 19 août 2026 | 00:48:14 | |
We took total strangers for rides down the racetrack in our diesel drag trucks, and it might be the most fun thing we've ever done at an event. This episode is a stroll down memory lane on the Power Driven Podcast, covering our trip to Montana for an NHRDA event and the first time each of us felt real horsepower behind the wheel. Todd, Will, and Myer break down how the spectator ride along program came together, from a six year old getting the full harness experience to grown adults walking away shaking after a pass in the junker. We also cover what it takes to run those rides safely, watching trans temps and checking for leaks between passes. Then we get into the technical side of the weekend. Myer talks through setting a new record for the fastest Dodge 48RE four speed transmission in a truck, running a 4.82 at 155 miles per hour in the eighth mile, and the tuning fix that got him there. There is a breakdown of why guys are moving from the 48RE to turbo 400 transmissions for pro street and eighth mile racing, and why the converter clutch dragging at the line is the real Achilles heel of the Dodge trans. We also talk diesel truck racing classes, from mild 770 index trucks up to 590 Pro Street, and why a stock looking Cummins powered truck sitting in the parking lot could probably run mid elevens if the owner just gave it a shot. We had a blast being part of this NHRDA event and hope to see more tracks doing spectator ride alongs. Come say hi in the pits if you catch us at the next NHRDA race in Ennis, Texas this September. If you enjoyed this one, subscribe on YouTube and follow the Power Driven Podcast on your favorite podcast platform. Whether you're thinking about getting into diesel drag racing, building your own eighth mile truck, or fixing up your Dodge four speed, we've got you covered. Shop everything you need at PowerDriven.com. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Blown Head Gasket? Here's What You're Doing Wrong | 11 août 2026 | 01:02:02 | |
Blown head gaskets are one of the most common headaches diesel guys run into once they start chasing real power, and this episode breaks down exactly why they happen and how to actually fix it for good. Todd, Will, and Myer get into it after a viral clip of a 6.7 Cummins shooting fire straight out the front of cylinder number one, and use it as the jumping off point for a full breakdown of head gasket failure. The guys tackle the biggest myth in the diesel world first, that high drive pressure is what blows head gaskets. It is not. High cylinder pressure from advanced timing is the real culprit, and they explain why a tighter turbo setup that makes drive pressure is just a sign of an engine that is going to make power down low, which is where the real cylinder pressure spike happens. From there the conversation moves into sealing solutions, starting with fire ring gaskets and split firing, which the guys call the ultimate ceiling technique for a high performance diesel build. They compare that to Top Fuel dragster hoops and C ring style seals, and explain why a fire ring is still the go to for iron block Cummins applications running big power, whether it is a 12 valve, a 24 valve, or a VP44 setup. There is a deep dive into crush specs, retorque procedure, and the difference between how MLS gaskets and older factory gaskets handle a little bit of leakage, along with the common mistakes guys make when resurfacing a head at home with the wrong tools. The guys also walk through real world troubleshooting, covering coolant leaks after a firing job, how much crush is too much, and what brands like Hazel and Industrial Injection are doing differently with their gasket specs. If you are building a diesel truck for serious horsepower and want to avoid blowing a head gasket, or you are already dealing with one and trying to figure out why, this episode gives you the real explanation instead of the Facebook forum version. Subscribe to the Power Driven Podcast on YouTube and follow along on your favorite podcast platform so you never miss an episode. This episode is all about head gasket sealing, and the fire ring head gaskets Todd, Will, and Myer talk about are built and sold right through Power Driven Diesel. Shop everything mentioned in this episode at PowerDriven.com Shop Power Driven Diesel: https://www.powerdriven.com | |||
| We Broke Down Every Cummins Camshaft | 04 août 2026 | 01:02:03 | |
Todd, Will, and Myer are back for round two on camshafts, picking up right where they left off and going even deeper into diesel cam theory. If you got something out of the last episode, this one takes it further with real numbers, real data, and some genuinely nerdy breakdowns that most Dodge Cummins guys never get access to. This episode is built around volumetric efficiency and how race engines actually push past 100 percent. The crew explains scavenging, low pressure zones, and how intake air speed changes everything about when you should close that intake valve. They break down piston speed and rod angle, why 70 degrees after top dead center is the sweet spot for airflow, and why valve lift speed is limited by lifter size, which is a big reason Cummins runs such a massive lifter compared to the gas world. From there Will pulls out actual cam data measured off real factory camshafts using a cam doctor tool, comparing intake and exhaust duration and valve timing across every generation of Cummins, first gen, 12 valve, VP44, and common rail. The differences in exhaust valve opening timing alone explain a lot about why certain Cummins generations start easier, burn cleaner, or make power differently. They also dig into intake and exhaust centerline angles and why lifting the valve higher instead of just chasing bigger duration numbers is often free horsepower with no downside. The back half covers valve springs, coil bind, and why some aftermarket cams cause problems with stock components, plus a preview of a project cam being custom built for an upcoming race truck this September, designed specifically around a narrow RPM window instead of chasing bigger numbers across the board. If part one gave you the foundation, this episode is where it gets real. Whether you are running a first gen, a 12 valve Dodge Cummins, a VP44, or a common rail, this breakdown gives you a real foundation on how factory and aftermarket camshafts are actually engineered. Subscribe on YouTube and follow the podcast on your platform of choice so you catch the rest of this camshaft series as it drops. Colt Cams are now part of the Power Driven lineup, so if you want to dig deeper into the camshafts covered in this episode or see what fits your Cummins, head over to PowerDriven.com to check out the full selection. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Power Driven Just Bought The Most Legendary Name In Diesel Cams | 31 juil. 2026 | 00:48:35 | |
This week Todd, Will, and Myer sit down to talk about something that gets asked about constantly but rarely gets explained right, camshafts. If you have ever wondered why your buddy's diesel sounds smooth while another one lopes like a muscle car, or whether a bigger cam is going to kill your fuel economy, this episode breaks down exactly what is going on inside your engine and why diesel camshafts do not follow the same rules as gas performance builds. The guys also announce something big for the diesel performance industry. Power Driven has acquired Colt Cams, the original name in diesel camshaft development founded by Jeff Colt, and it is now officially under the Power Driven umbrella shipping out of America. The crew talks about what owning that brand outright means for R&D moving forward, including in house cam design and testing on their own engine dyno. From there the conversation gets into real cam theory. Todd, Will, and Myer explain why diesel duration numbers look nothing like gas cam numbers, why a factory Cummins cam is built around torque and RPM range instead of high end horsepower, and why a bigger cam on a Cummins diesel tuning setup usually helps fuel economy instead of hurting it. They cover the difference between 12 valve and 24 valve Cummins camshaft design, how a single lobe activates two valves through the bridge setup, flat tappet versus roller lifter reliability, and why the intake valve closing point is considered the most important event in camshaft design. Whether you are running a 12 valve, a 24 valve, or a common rail Cummins, this episode gives you a real foundation on volumetric efficiency, cam terminology, and how to think about camshaft upgrades the right way instead of just chasing bigger duration numbers. This is part one of a deeper camshaft series, so if you want to understand what is actually happening inside your diesel engine, this is a good place to start. If you learned something from this one, subscribe on YouTube and follow the podcast wherever you listen so you do not miss the rest of the camshaft series. Colt Cams are now part of the Power Driven lineup, so if you are looking to upgrade your camshaft or just want to see what is available for your Cummins, head over to PowerDriven.com to check out the full selection. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Your Diesel Truck Is Overheating and You Don't Even Know It | 21 juil. 2026 | 01:04:19 | |
It's towing season and if your gauges are climbing on the way up the grade, you need to know what's actually normal and what's a real problem. Will and Myer break down coolant temps, transmission temps, and everything that can push a Dodge Cummins diesel truck out of range while towing. They start with what a healthy cooling system looks like going down the road. Thermostat opening temps on these trucks typically run 180 to 200 degrees depending on year and setup, and they explain why a hotter or cooler thermostat matters for winter heat versus summer towing, along with how boiling points, radiator cap pressure, and elevation all affect what your coolant temperature can handle. A big part of the episode covers fan clutches, since a bad cooling fan clutch is usually the first thing they check when a diesel truck runs hot. They explain how to tell if your mechanical fan clutch is engaging and why electric fans aren't actually an upgrade over the factory setup on these Cummins trucks. From there they walk through testing a thermostat the old school way with a pot of boiling water, the bypass port a lot of guys don't know exists in the block, and why a genuine Cummins thermostat is worth it over the cheap parts store version, especially on a second gen Dodge. Radiator condition gets its own conversation too. They cover why a clogged or dirty radiator causes most cooling problems, why a factory copper core radiator often beats a cheap aftermarket one, and how they've flushed old radiators back to life with everything from radiator flush products to straight vinegar. They also get into heater core plumbing and why oversized fittings from a repipe can hurt your cooling in the summer. The conversation wraps up on transmission cooling, the second gen's heat exchanger setup, why factory transmissions are designed to run around 185 degrees, and why colder fluid on a built performance transmission tends to live longer. Along the way Will and Myer share real diesel towing stories, from Willard's cooling performance on a run to Saint George to a second gen Dodge gauge that pegs out hard at 230 degrees, plus a few lessons learned the hard way about fan clutches and stuck thermostats. If you found this useful, subscribe to the Power Driven Podcast on YouTube and follow along on your favorite podcast platform. Will and Myer reference several parts from their own builds throughout the episode, including compound turbo setups, VGT turbochargers, and stage two and stage three injectors. Shop everything mentioned in this episode at PowerDriven.com links below. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| UCC Comments Got Heated, Here's Why They're Wrong | 08 juil. 2026 | 01:12:52 | |
Myer just won the Ultimate Callout Challenge, and now that the documentary is out, the comments section has some strong opinions about it. Todd and Myer sit down together this week to work through the feedback and clear up a few misconceptions about what UCC actually is. Most of the response has been positive, and the guys are genuinely grateful for it. But this episode digs into the comments they disagree with, starting with the drag race side of things. The truck runs a 48RE, a Dodge automatic out of the 2003 to 2006 trucks, built around the largest input shaft currently available in a 35 spline. They actually brought two built transmissions to the event on purpose, and they explain why. On the dyno, a lot of people got upset about how fast the pulls looked and how much time the truck spent under load. They break down why that criticism misses the point. Competitors do not control the resistance on the dyno, the competition sets it, and every truck gets the same load. More power against a fixed resistance just means the run finishes quicker. They also cover why UCC moved away from scoring torque plus horsepower years ago, after competitors found ways to game that formula with gearing. From there the conversation covers the aftermarket ECU running the whole truck, from injectors to timing, the mag valve controlling the second turbo, and why the nitrous stayed conservative until high rpm to keep the engine alive through the pass. The sled pull gets its own breakdown too. Some commenters claimed the team ran three different trucks across the weekend. Todd and Myer clear that up. It is one drag chassis that also runs the dyno, then gets an axle and bracing swap for the sled. They also cover the sled weight box getting adjusted mid competition and why there is no out of bounds penalty in this class. The bigger theme running through the episode is what UCC is actually built for. It is an invitation only event with almost no restrictions outside a weight limit and hitch height, designed to see what the industry can build without limits, not a street truck competition. If this episode got you fired up, subscribe on YouTube and follow along on your favorite podcast platform. This build runs on parts that get proven under real pressure, not just talked about. If you want that same confidence in your own truck, PowerDriven.com is where to start. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| 650 HP 12 Valve Destroyed by Nitrous | Now a 1100 HP Stroker | 26 juin 2026 | 01:02:57 | |
Kyle from Dark Iron Diesel flew his blown up 12 valve Cummins out to Power Driven Diesel so the crew could rebuild it from the ground up, and this episode follows the build while the guys dig into what actually separates a fast truck from a truck that just sounds fast. Kyle's 12 valve made 650 horsepower before a nitrous mishap put a freeze plug through the block and warped the head. Instead of a simple repair, Todd, Will, and Myer turn it into a full stroker build, taking the 5.9 out to a 6.1 liter on a 6.7 Cummins crank that Power Driven now manufactures in house. They cover custom Wagler rods, ceramic coated pistons, a reconditioned head, a Colt Stage 4 cam, and an Aggressor 60/65 over 98 compound turbo setup aimed at 1100 to 1200 horsepower. We filmed the full teardown, machine work, and stroker crank install start to finish, so keep an eye out for the build video covering every step of this engine in detail. The crew also compares Myer's 1300 horsepower race truck against Kyle's Lamborghini Huracan, which he had on hand from a cross country supercar rally, breaking down 0 to 150 times and why horsepower alone does not tell the story without weight and traction factored in. Kyle also talks about walking away from a potash mine job to do YouTube full time and his approach to dyno testing. Subscribe on YouTube and follow along on your favorite podcast platform. This episode covers a full engine build, parts, and machine work, all done in house at Power Driven Diesel. If you want to build something similar, the team can help you spec it out at PowerDriven.com. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Why MORE Horsepower Is LOSING In 72 Fast Diesel Racing | 17 juin 2026 | 00:55:42 | |
Todd, Will, and Myer dig into Fast 72, the new turbo limited diesel racing class that is already turning heads and stacking serious prize money. A single 72 millimeter turbo and a fuel only setup are producing six figure purses, and this episode breaks down why. They start with the actual rules of the class. No nitrous, no water injection, no methanol, just engine, turbo, and chassis. From there they get into why the trucks making the biggest peak horsepower numbers on the dyno are not always the ones winning at the track, and why second gen Cummins trucks keep running away with it the same way they have been dominating UCC. That leads into camshaft talk. Overlap, intake valve closing events, and how RPM range should dictate cam selection, and why a cam that makes huge peak numbers can actually bleed off boost and lose power down the track. The conversation then shifts to cylinder heads, covering valve sizing, port flow, and why a factory piston might outperform a forged piston at this power level. There is also a quick detour into transmission durability, since the top two finishers in this class are both running stock automatics, plus a reminder that this is not a high dollar class. Anybody with an engineering mindset can be competitive here. They close out talking about the next Fast 72 event in Texas this September, with a purse north of one hundred forty thousand dollars on the line for the season finale. If you are into diesel performance, Cummins builds, or smart engineering beating raw horsepower, hit subscribe on YouTube and follow the show on your favorite podcast platform. Everything the guys talked about when it comes to cams, cylinder heads, and turbo limited builds is the kind of work Power Driven Diesel lives in every day. Head over to PowerDriven.com to check out the full catalog and get your own build dialed in. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| How Myer Set The All Time Points Record At UCC 2026 | 12 juin 2026 | 02:18:18 | |
Myer just made history at UCC 2026, becoming the first competitor to ever break the 3,000 point barrier with a total score of 3,393. This week Will sits down with Myer and guest Josh McCormack, a UCC 2025 competitor, to break down every run, every number, and every decision that went into the most dominant performance the event has ever seen. Across three days of competition, Myer opened on the drag strip with a 4.903, followed it up with 3,620 horsepower on the Super Flow dyno to bank more than 1,200 points in that session alone, and closed out the weekend with a 355 foot sled pull. The crew breaks down the tuning decisions, the overnight chassis conversion between dyno day and sled pull day, and what it actually takes to put up competitive numbers across all three disciplines in a single weekend. Having Josh in the room as a past UCC competitor adds real perspective to the debrief. The guys talk through what separated the top finishers from the rest of the field, why the West Coast teams dominated the leaderboard, and why pre-event testing at the drag strip and dyno is the difference between contending and just showing up. They also get into the sled pull setup, what happened on Myer's pull, and what the points game looks like when you are genuinely building toward something no one has ever done before. This is an honest debrief from the guys who built the truck, drove it, and rewrote the record books at one of the most demanding diesel performance competitions in the country. Subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or wherever you listen. Everything Power Driven Diesel builds and sells is at PowerDriven.com. If this episode got you fired up, go check out what the shop has to offer. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| We Built the Craziest Cummins We've Ever Made to Compete at UCC 2026 (Here's Everything We Did) | 27 mai 2026 | 01:23:42 | |
Myer is one week out from the Ultimate Callout Challenge and the second gen Cummins build he has been hammering on since November is almost ready. In this episode Todd, Will, and Myer break down what the truck has become and what they are showing up to Indiana to do. They cover the full transformation from street truck to UCC competitor, including the chassis work, the new deck plate engine, the Bosch ECM swap, a custom Air Dog lift pump, and the wild sled pull sub chassis that rolls completely in and out from under the truck without touching the weight box. They also get into testing results from Arizona and Vegas, including a 4.99 eighth mile pass on a 848 with a stock computer. If you are thinking about making the trip to UCC this year, this episode is the reason to go. The field is stacked, the builds are insane, and Myer's truck is one of the most creative setups on the property. Subscribe on YouTube and follow on Spotify or Apple Podcasts so you catch the full UCC recap when the crew gets back from Indiana. Everything you need for your diesel performance build is at PowerDriven.com. Shop Power Driven Diesel: https://www.powerdriven.com 0:00 Intro and UCC one week out 1:45 72 Fast class and the $70k purse 3:00 Papa Saurus origin and Commonwealth swap 6:30 Cage build and chassis work 9:45 Arizona debut and first passes 20:30 Vegas test and tune 25:15 Breaking the five second barrier 28:30 The sled pull sub chassis explained 42:00 New deck plate engine overview 54:00 Air Dog custom pump and Bosch ECM upgrade 1:08:30 UCC goals for drag, dyno, and sled pull 1:18:00 AI says Myer has no chance | |||
| Essential Gear Every Modified Diesel Owner Needs to Carry | 19 mai 2026 | 00:59:51 | |
If you run a modified diesel truck, a roadside breakdown is not a matter of if. It is a matter of when. Todd, Will, and Myer dig into their best and worst breakdown stories to help you prepare for the inevitable before summer hauling season gets here. The guys cover everything from blown intercooler boots and dead alternators to turbo failures, low oil pressure, and full engine carnage. Most of their stories happen while hauling a trailer, which is exactly when you do not want to find out your diesel performance build has a weak link. Some of these repairs got made on the side of the road with whatever was on hand. Others required a little creativity, a few phone calls, and people willing to help. Along the way they hand out practical tips that apply to any diesel truck build, whether you are running a built second gen Cummins, a 12 valve, a 24 valve, or a common rail. Good intercooler boots, tight clamps, a tire plug kit, spare fluids, and a basic tool kit can solve a surprising number of problems that would otherwise leave you waiting on a tow truck. The bigger takeaway is that preparation before a trip matters more than any roadside fix. Check your tires, top off your fluids, inspect your battery terminals, and make sure you have the right tools before you leave the driveway. Machines break. The guys who handle it best are the ones who saw it coming. If you haul, race, or travel long miles in a diesel truck, this one is worth your time. Subscribe to the Power Driven Podcast on YouTube and follow along on Spotify, Apple Podcasts, or wherever you listen. Shop everything mentioned in this episode at PowerDriven.com, including intercooler boots and everything else you need to keep your diesel truck on the road when it matters. Shop Power Driven Diesel: https://www.powerdriven.com 0:00 Intro and episode overview 0:45 UCC context and Myer's trip to Indianapolis 2:00 The Mac: Ford Aero Max with 855 Cummins mechanical PT pump swap 4:15 Coming home from UCC with a blown turbo in the Midwest 5:30 Will Terry Fabrication: stovepipe turbo fix with Ace Hardware parts 7:55 Garrett 475 swap, T6 flange mismatch, and getting over the Rockies 9:45 Intercooler boots: when they blow and why it happens 12:00 Boot maintenance tips, clamp torque, and upgrading before you haul 13:15 Alternator trigger wire failure and diagnosing on the fly 21:00 Broken Smith Brothers pushrod strands the family truck 28:30 Alternator failures: 6.0 Power Stroke and the Las Vegas story 30:45 Montana breakdown: getting a store employee to deliver an alternator roadside 35:00 Low oil pressure on the 12 valve, loose turbo drain bolt, flagging down semi drivers 39:15 Cracked billet flex plate discovered on the way home 44:00 Carrying spare fluids, radiator hose stories, and what to keep in the bed 45:45 Transmission cooler bypass trick with a pair of pliers 46:45 Tire plug kit and 12-volt compressor: the tools that solve simple problems fast 48:00 Boonie kit concept and the pantyhose serpentine belt story 49:20 Always carry a flashlight 49:45 The value of a good friend network when you are stranded 51:55 Tyson borrows the truck and puts holes in the block 55:30 Pre-trip checklist: tires, spare, fluids, spline lug socket, battery terminals | |||
| What to Look For When Buying Someone Else's Unfinished Project | 12 mai 2026 | 00:56:41 | |
Buying someone else's unfinished project truck sounds like a shortcut, but it can turn into one of the most expensive decisions you make. Todd, Will, and Myer break down exactly what to watch for when you're rolling up to a used diesel truck with a head full of optimism and a wallet that needs to survive the trip. The guys get real about why sellers abandon projects in the first place, and why that reason matters more than the deal itself. Money, time, boredom, a problem they couldn't solve, all of it changes what you're actually inheriting when you hand over the cash. Not every truck listed with cool parts is worth what the seller thinks it is, and not every deal is what it looks like on the surface. A big part of the conversation is the physical inspection. Pop the hood and you can tell a lot fast. Firewall insulation and hood insulation are some of the first things to check because they tell you how many times someone has been in there and whether they cared when they put it back together. Wiring is another one. If you see bare twisted wires and electrical tape where a proper loom should be, that truck is telling you something and you should listen. The guys also talk through the secondary market and the reality of flip sellers on classifieds who buy trucks cheap, patch a surface problem, and resell without any real knowledge of the vehicle history. Knowing the difference between a guy who built something and a guy who bought it to move it is one of the most useful skills you can develop when shopping for a project. They cover transmission talk specific to Dodge trucks, including what a shop-claimed "heavy duty" or "towing" transmission actually means versus a real built trans, and why you need to ask the right questions before you assume the drivetrain is sorted. For Cummins trucks from 2019 and up, there is also a conversation about the hydraulic roller lifter design and the failure concerns that make some buyers think twice about the newer platform when they are looking for something they can actually work on and source parts for. The episode closes with the bigger question every buyer has to answer honestly before they shop: are you someone with the tools and knowledge to take on whatever you find, or are you someone who needs to start with a cleaner slate and let a shop handle the build. Neither is wrong, but getting that answer wrong before you buy can cost you a lot more than you saved. If you are looking to pick up a diesel project truck, pull up a chair because this one is worth hearing before you write that check. Subscribe on YouTube and follow on your favorite podcast platform so you never miss an episode. | |||
| Cummins Engine Building Tips Part 2: Bearings, Break-In, and First Fire | 05 mai 2026 | 01:35:46 | |
Part two of the engine building series picks up right where things left off, covering everything from bearing installation all the way through first fire and ring break-in. If you are building a Cummins or planning to, this is the episode you do not skip. Todd, Will, and Myer break down the full Morley bearing lineup, covering P, H, and V bearings and which one belongs in which build. Coated bearings, bearing installation technique, and why cleanliness between the bearing and saddle matters more than most guys realize all get covered in detail. Plastic gauge gets a thorough breakdown too, including an honest story about what happens when you misread a dial bore gauge. Wrist pin clip orientation, rod direction by platform, crank galley cleaning, and which way rods go in a 12 valve versus a 24 valve versus a VP44 are all walked through in real shop language. So are crank gear welding, cam retainers, piston protrusion targets, firing head gasket installation, head stud torque sequence, and valve lash strategy. The break-in section is worth the entire runtime on its own. Proper cam break-in, why you do it without coolant in the block, how to track oil temp with an infrared gun, and why ring break-in requires load are all covered. The crew explains why babying a fresh built diesel causes glazing and oil consumption issues, and breaks down break-in oil, first oil change timing, and cutting open the filter to check for debris. If you are wrenching in the garage and want to build a Cummins that lasts, subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or wherever you listen. Everything the guys talked about in this episode, including Morley bearings, assembly lube, and Power Driven Diesel oil, is available at PowerDriven.com. Links below.
| |||
| How to Build a Cummins Engine the Right Way (Part 1) | 28 avr. 2026 | 00:54:18 | |
If you have ever cracked open an engine block and wondered whether you are missing something the shop guys never talk about, this episode is for you. Todd, Will, and Myer break down the real hands-on engine building process, step by step, using their Myers UCC build as the backdrop for a conversation that covers everything from the stuff you check before you turn a wrench to the stuff that will bite you if you skip it. The episode kicks off with oil galley plug inspection, what the guys call the oil rail, oil rifle, or oil passage depending on who is talking, and why making sure every one of those plugs is seated before assembly is a non-negotiable. They get into cleaning procedures using an engine bore brush kit to pull out machining particles and metal flakes from the cylinder bores and oil passages before anything goes back together. Bearing clearances get a solid breakdown here. The guys walk through main bearings and rod bearings on a Cummins engine, explain why the oil holes in the bearings do not line up the way you might expect, and talk through what proper clearance looks like for street builds versus high RPM race applications. They also hit a detail that trips up a lot of first-time builders: rod caps are matched to their specific rod during the machining process, and swapping caps between rods will cost you roundness and likely an engine. Cylinder wall prep takes up a good chunk of the conversation too. The guys reference using the Total Seal ring break-in compound to verify cleanliness, where green means the wall is ready and brown means you are not done yet. From there the discussion moves into piston ring gap, how they set the second ring at or slightly larger than the top ring, ring orientation during installation, and their experience running Total Seal gapless second rings at higher horsepower levels where piston land strength starts to become a real concern. The back half of the episode covers assembly lube, specifically the Joe Gibbs Driven line and other black assembly greases the guys have had good results with, where to apply it and where not to, and the proper way to lube a camshaft, lifters, and cam lobes before the engine goes together. The cylinder head side of the build runs long and gets pushed to next week, so consider this Part 1 of a two-part deep look at what it actually takes to build a diesel engine the right way. Subscribe on YouTube to catch Part 2 the moment it drops, and if you are listening on Spotify or Apple Podcasts, follow the show so you never miss an episode. Everything the guys talked about in this episode, rings, bearings, assembly products, all of it is the kind of stuff you can find at PowerDriven.com. If you are building an engine, start there. Shop Power Driven Diesel: https://www.powerdriven.com 0:00 Intro and Mars UCC engine build overview 1:18 Oil galley plugs and why they cannot be overlooked 2:30 Cleaning oil passages and cylinder bores 4:13 Main bearing installation and oil hole alignment 5:03 Measuring journals and bearing clearances 7:07 Cylinder wall prep and final cleaning order 10:00 Total Seal break-in compound and cylinder wall verification 10:35 Measuring rod journals, main journals, and bearings 12:30 Bearing clearance specs for street vs race applications 13:24 Why race clearances and thick oil do not work on a street truck 18:33 Rod cap and rod matching on Cummins and aftermarket rods 29:52 Piston ring clearance and piston wall clearance 31:42 Ring gap setup and second ring sizing 33:34 Ring orientation during installation 40:37 Total Seal gapless second ring discussion and high HP concerns 42:06 Loctite, fasteners, and oil galley plug sealing 49:15 Assembly grease selection and application 52:25 Camshaft and lifter lubrication 53:45 Episode wrap and Part 2 preview | |||
| The Truth About Diesel Pistons: Cast vs Forged, Bowl Design, and What to Run in Your Build | 21 avr. 2026 | 00:46:27 | |
Pistons are one of those parts everybody installs but not everybody actually understands. Todd, Will, and Myer break down piston design from top to bottom, and if you have ever wondered why there are so many options or which one belongs in your build, this is the episode you need. They start with piston bowl design and why it matters more than most guys think. Narrow bowl versus wide bowl, reentrant versus non-reentrant, and how each design affects the way fuel and air mix inside a diesel cylinder. Because diesels fire fuel directly into that bowl at the very end of the compression stroke, bowl geometry has a direct impact on combustion quality, smoke, and power output in a way gasoline engines never have to deal with. Swirl numbers get covered too, and why that circular mixing motion plays a bigger role in emissions and haze than it does in outright peak power. The conversation moves through piston options platform by platform. Common rail, 24 valve, VP44, and 12 valve all get their own breakdown. The guys talk about why they almost always steer people toward a narrow bowl for over-the-road use, but also when a wide bowl makes sense, like sled pulling and nitrous-limited classes where you are chasing every last horsepower. Cast versus forged is a big chunk of this episode and the guys do not sugarcoat it. Forged pistons are stronger and handle RPM abuse better, but the increased wall clearance required, the wear characteristics, and the oil ring differences make them a poor choice for anything that sees regular street miles. They even mention their factory 6.7 cast pistons surviving a truck that averages 2200 horsepower down the track, and what that says about how capable a properly built cast piston really is. The 12 valve guys get their section too. Stock pistons, the early first gen wider bowl swap, and why the shop has largely moved away from recommending low compression pistons now that six seven blocks are the go-to platform for high-output Cummins builds. Piston coatings and cylinder honing round out the episode. The guys cover their coating experiments on Myer's race truck, what coatings can and cannot protect against, and why proper piston wall clearance is still the thing that determines whether any of it survives. Subscribe on YouTube and follow the Power Driven Podcast on Spotify or Apple Podcasts so you do not miss episodes like this one. Everything from pistons to full build components for your diesel is available at PowerDriven.com. If anything from this episode sparks a build question, the team there can point you in the right direction. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| How a Simple Engine Ran 4.99 in Pro Street Diesel | 14 avr. 2026 | 00:55:27 | |
Myer's drag truck just ran a 4.99 in the eighth mile, and the engine making it happen is almost offensively simple. On this episode of the Power Driven Podcast, Todd, Will, and Myer break down what it took to get there and why the technology available to diesel builders right now is changing what is possible at every level of the sport. The guys dig into what that number actually means in context, where the money goes in a build like this, and why high level diesel performance is more attainable today than it has ever been. The conversation covers everything from drivetrain decisions to turbo costs to cylinder head development, all through the lens of what it took to put a tow truck in the fours. Pro Street diesel is growing fast and the boys make a strong case that now is the time to get in. Multiple trucks are running deep fives and dipping into the fours, the parts are better, and the price to compete has come way down compared to even a few years ago. Everything the guys talk about in this episode is available at PowerDriven.com. Links below. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Why Your Diesel Tows Like Garbage (And How To Fix It) | 07 avr. 2026 | 00:57:28 | |
Every diesel guy has been there. The truck feels great empty, pulls hard, and you love it right up until you hook a trailer to it. Todd, Will, and Myer dig into exactly why that happens and what you can actually do about it. The conversation starts with a real story about building a 12 valve for power without thinking about what it would have to do. Big pump, big single turbo, five speed, and a trailer to tow. The result was exactly what you would expect from a setup built for the strip and not the highway. It towed, but it was miserable, and that experience sets up everything else in the episode. From there the guys get into tuning strategy for trucks that need to work. Pedal mapping and throttle input are a bigger deal than most people think, especially when your transmission is mechanically activated and does not know your engine is making twice the power it was designed around. If your transmission thinks you are at light throttle while your engine is at full pull, you are going to have a bad time. Getting the tune and the transmission working together is step one. Turbo selection comes up as one of the biggest places guys go wrong when building a tow truck. Oversized turbos that are great for making peak power numbers are often terrible for towing because they surge, they come on hard, and they kill drive manners under load. Compressor wheel clearances also factor into efficiency and reliability in ways most people do not think about. The right turbo for towing is not the biggest one you can bolt on. Fuel system choices matter too. Massive injectors and multi-pump setups introduce complexity and reliability concerns that become a real problem when you are stranded on the side of the road a long way from home. For a dedicated tow truck, simple and reliable beats flashy every time. Carrying spare parts because you know your setup is likely to break is not a strategy. Tires are another thing that can quietly kill your tow truck. Load ratings, tire size, and how they affect your effective gear ratio all play into how your truck behaves under a load. Going up in tire size without accounting for everything downstream can smoke a transmission and make towing miserable regardless of what else you have done to the truck. The core takeaway is something the guys come back to repeatedly. You have to decide what your truck actually is before you build it. A dedicated tow truck and a street truck that occasionally tows are two completely different builds. You can have a modified truck that tows great, but the parts and strategy have to match the application. If you are building a diesel and towing is part of the plan, this episode is worth your time. Subscribe on YouTube and follow the Power Driven Podcast on Spotify, Apple Podcasts, or wherever you listen. Everything discussed in this episode is available at PowerDriven.com. If you are building a tow truck or a street truck that needs to work, the team can point you toward the right parts for your application. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Why the Diesel Community Is Calling Todd a PURSE POACHER | 31 mars 2026 | 00:47:30 | |
Todd poached a purse and the diesel community is not happy about it. He showed up to a Blue Collar class drag race in Phoenix with a high mileage Cummins truck, a nitrous setup thrown together the night before from used shop parts, and no real plan to win. Then he won. Now there are posts. Now there are opinions. And now Todd, Will, and Myer are here to talk about it. The truck was not purpose built for the class. It fit the rules close enough to enter and that was the whole strategy. A 62mm turbo, a 52 jet, and a flat foot launch that just happened to hook. No PDD resources, no race prep, no endless planning. The guys break down the full story, get into the spirit vs. letter of the rules debate that followed, walk through exactly what was on the truck, and dig into whether nitrous should be banned from the class or just opened up to everyone with a standardized jet. | |||
| Everything You Need to Know About Cummins Engine Blocks | 24 mars 2026 | 00:52:47 | |
Not all Cummins blocks are built the same, and if you are pushing serious power, the one under your hood matters more than most people think. Todd, Will, and Myer break down the full spectrum of Cummins engine blocks in this episode, from the various 12-valve generations to the 5.9 common rail and the 6.7, and explain exactly why the differences matter when the power numbers start climbing. The 6.7 gets a lot of attention here, and for good reason. The conversation covers what makes it structurally superior to earlier platforms: a thicker deck, a larger bore, longer wrist pins, and pistons that have held up to 3,000 horsepower in competition builds without giving up. The guys talk through how modern tuning lets builders get even more out of what is essentially a factory race motor sitting in everyday trucks, and why the 6.7 has earned its reputation as the current king of Cummins diesel performance. The 12-valve conversation goes deeper than most. There are meaningful differences between block variations that matter at high power levels, and the guys cover what to look for. Power Driven offers a 14-millimeter main stud upgrade across their block lineup, including as a standard feature on their 12-valve block, because the math on clamping force versus a stock bolt simply does not leave room for argument. One topic worth paying attention to is the roller lifter issue on newer 6.7 trucks. The guys call it out as a real problem already hitting a significant number of engines, potentially on the scale of what the VP44 pump failure was for the 24-valve crowd. If you own a 2019-and-up Ram with a 6.7, this part of the conversation is worth your time. There is also a breakdown of why dropping a 12-valve head onto a 6.7 block causes combustion problems. The 12-valve injector enters the cylinder at an angle, so the piston bowl is offset toward that injector. A centered bowl piston paired with an off-center injector creates combustion characteristics nobody wants. It is a simple geometry explanation that answers a question the comment section apparently asks regularly. The guys wrap up with some real-world context, including Todd running 10-second passes in his tow truck and a story about winning the fastest pass at an airport drag race against mustangs and a supercharged F-150 on a 6.90 slip. The point being that the power these engines support on the street right now is genuinely historic. If this episode has you thinking about your next block build, Power Driven has you covered with prepped and upgraded Cummins blocks and everything else mentioned in the episode at PowerDriven.com. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| We Went to NHRDA Arizona And Won $20,000 | 17 mars 2026 | 01:17:59 | |
The crew is back from Arizona and this one is worth every minute. Todd, Will, and Myer all showed up to the NHRDA Arizona event with trucks ready to race, and nothing went according to plan in the best possible way. If you have ever thought about getting into diesel motorsports, this episode is going to push you over the edge. The NHRDA Arizona event was a well run show under new ownership that delivered on the details, from clear signage to efficient staging lanes to bonus qualifying rounds when time allowed. The crowd was big, the energy was right, and even a PDD shop employee who had never raced before got talked into running Willard the tow truck and came back asking where he could buy one. That is what these events do to people. Todd lined up in the NHRDA Blue Collar class with Vin D against a stacked field of modern power and a $20,000 winner take all purse on the line. The 12 valve Cummins pump gun had something to say about how that ended. Will brought Uncle Rico to the 590 class, qualified strong, and had a legitimate shot at a trophy run before the motor had other ideas on Saturday morning. Myer's Scrat build finally made it to the track after months of fabrication and a last minute Thursday night dyno session that gave everyone just enough confidence to load up and go. The truck made an impression in a hurry. The episode closes with the burnout contest, the Junker, a neutral drop on compound boost, a wall, an exploding fan clutch, and a water methanol tank that had the track crew convinced there was a fuel spill on their hands. If you want to race and you have been sitting on the fence, get a truck ready and show up to an NHRDA event. You do not need an expensive build and nobody is going to give you a hard time for being new. More events are on the calendar including Indiana in June and Montana in August. Several of the parts and components discussed in this episode are available at PowerDriven.com. Whether you are building a race motor, putting together a transmission, or just keeping a working truck alive, the shop link is below. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Why Bigger Turbos Are KILLING Your Cummins Tow Rig | 10 mars 2026 | 00:53:50 | |
If you have ever second guessed whether you have the right turbo on your truck or just assumed bigger always means better, this episode is going to sort that out with real numbers from real trucks pulling real weight. Todd, Will, and Myer just got back from hauling to a race in Phoenix and brought the data to prove what properly sized turbochargers actually do out on the road. The guys recap the full tow to the NHRDA event, covering how Willard, their VP44 powered second gen, hauled over 22,000 pounds while running the 60-64 turbo with almost no smoke, no heat issues, and solid boost numbers from Cedar City all the way down to Phoenix. On the other side of that convoy, Myer was pulling 31,000 pounds in his 6.7 common rail tow truck running the Aggressor 480 in a compound setup, holding 30 pounds of boost against 27 pounds of drive pressure the entire way. That kind of boost-to-drive ratio does not happen by accident, and they break down exactly why it worked so well including how a ported cylinder head and cam combination keeps heat out of the air charge and off the radiator when you are working hard under a heavy load. From there the conversation moves into waste gate strategy for both single and compound setups, covering screamer gates, hot pipe gates, and what they learned while tuning the junker for burnout contest reliability at 130-plus pounds of boost. They also get into how nitrous changes the entire equation when it comes to getting exhaust volume out of the system fast enough to keep turbos alive. The guys cover the Aggressor 62-9 and 67-9 singles after running them in the Blue Collar class at the event, including back-to-back comparisons on fuel only and with nitrous. There is a real conversation here about spool characteristics, turbine sizing, and why the 62-9 spools noticeably quicker and what that means depending on what you are actually doing with the truck. They also get into how wide you can spread compound turbo sizes before things fall apart, and the honest answer based on their testing might surprise people who assumed there was a hard limit. The junker running a 62-9 paired with an Aggressor 98 as the atmosphere charger is the case study, and the dyno results on that setup are worth hearing. The episode wraps with a practical breakdown of which turbo makes the most sense depending on your platform and how you use your truck, covering the tow series lineup across the second gen, common rail, and Power Stroke applications. If you are trying to figure out what to put on your rig this is about as straight of an answer as you are going to get from guys who have actually tested all of it. Subscribe on YouTube and follow the Power Driven Podcast on Spotify or Apple Podcasts so you never miss an episode. It is also March which means the Power Driven sale is live sitewide and they are giving away five Aggressor turbos to customers this month. Every hundred dollars you spend earns you an entry. Here is what is on sale: 👉 10% off all Power Driven products including heads, transmissions, pushrods, air filters, and oil 👉 15% off all PDD fueling 👉 15% off all PDD turbos 👉 20% off Power Driven True 6.7L Crankshafts If you have been sitting on a parts order this is the month to pull the trigger. Everything talked about in this episode including the Aggressor turbo lineup and the full tow series is available at PowerDriven.com, and if you have been sitting on a turbo upgrade, March is the month to pull the trigger with the sale running and five turbos being given away to customers. Shop Power Driven Diesel: https://www.powerdriven.com | |||
| Is A $10,000 Cylinder Head Worth It On Your Cummins? | 03 mars 2026 | 00:46:07 | |
What does it actually cost to build a diesel that makes real power? More importantly, what does it cost when you buy the wrong parts? This week on the Power Driven Podcast, the guys are pulling back the curtain on one of the most debated topics in the diesel performance world: cylinder heads. Whether you're building a Cummins street truck or chasing records in a purpose built race rig, the head you choose can be the difference between a truck that dominates and one that leaves you stranded with a pile of parts you can't use. The crew breaks down the real cost of high performance cylinder heads, from shelf heads running factory valves all the way up to full custom builds pushing toward the $9,000 to $10,000 range. They talk about why a premium head is an absolute must once you start adding big turbos, stacking boost, and pushing into serious horsepower territory on a diesel engine build. A poor flowing head will cap you out fast, no matter how much fuel and air you throw at it. But it's not all about top shelf builds. One of the most important takeaways from this episode is knowing what your truck actually needs. The guys get real about matching parts to your goals, because throwing a race spec head onto a 500 horsepower street truck is just burning money. They dig into the middle ground too, including valves, springs, connecting rods, and pistons, and how the diesel aftermarket is maturing to give builders more competitive options at better price points than ever before. They also give a glimpse into what's being developed in the shop right now for the upcoming UCC build, which is shaping up to be one of the most serious Cummins engine builds the Power Driven team has ever put together. Meyer has been deep in the R&D on a head that could set a new standard for the platform, and the guys are genuinely fired up about where it's headed. Spring is coming. Race season is right around the corner. If you've got a build on the table, this is the episode to listen to before you start buying parts. | |||
| We Accidentally Built the Perfect Race Truck | 24 févr. 2026 | 00:47:00 | |
What happens when a truck you built for testing accidentally becomes the perfect race weapon? That's exactly what we're dealing with heading into the NHRDA Diesel Desert Nationals in Chandler, Arizona, and we are fired up about it. In this episode of the Power Driven Podcast, we're breaking down everything you need to know about the brand new Blue Collar Class, a street truck drag racing format that is turning heads in the diesel performance world. No boost launches. No prepped surfaces. No Christmas tree countdown. They line you up, flip on a flashlight, and when it goes green, you go. That's it. It's the closest thing to a real stoplight race you'll find at a sanctioned event, and we are here for every second of it. The class has strict turbo size limits based on your platform, a 7,000 pound minimum weight requirement, and a 400 tread wear tire rule so you can't just show up on a full race setup and blow the doors off everybody. They want real trucks driven by real guys, and with a $300 entry fee and a $20,000 payout purse on the line, the competition is going to be serious. Here's the wild part. Our 12 valve test rig Vin-D, the truck we've been running injector tests, tow tests, and dyno pulls on for months, just so happens to sit right around 740 horsepower with a 67.9mm turbo and a towing cam. We did not build this truck for the class. It just worked out that way. Now we're going to dial in the wastegate, throw on some fresh rubber, and see what this thing can do when the light goes green from a dead idle. We also talk about which platforms have the real advantage in a class like this, why common rails could be tough to tame off the line, and what it would take to actually build the perfect Blue Collar Class truck from scratch. If you've ever wanted to go racing without dropping a fortune on a purpose built drag truck, this episode is going to get your gears turning. | |||
| The Diesel Mods That Are A Complete Waste Of Money | 17 févr. 2026 | 00:56:42 | |
Ever dropped a stack of cash on a diesel performance mod and wondered why your truck drives worse than before? Yeah, we've been there. In this episode of the Power Driven Podcast, Todd, Myer, and Will sit down in the race shop to talk about the modifications that people do to their diesel trucks that either flat-out ruin them or just don't deliver what they promised. We kick things off with the age-old debate about leveling kits, stance boy wheels, and oversized tires on diesel trucks. Will's got some strong opinions here, and if you've ever wondered why your second gen Dodge or third gen Cummins follows every groove in the asphalt like a shopping cart with a bad wheel, this is the conversation you didn't know you needed. Spoiler: your ball joints aren't happy either. From there we get into the performance mods that sound great on paper but end up costing you more than they're worth. We're talking oversized injectors, 13mm injection pump sizing on builds that have no business running them, and the classic mistake of throwing the biggest, baddest parts at a tow truck that just needs something sensible. We hear from guys constantly whose 12 valve Cummins or VP44 went from awesome to terrible overnight chasing a spec sheet. We also dig into the intake horn debate with real dyno testing data, cold air intakes, intercooler upgrades, diesel exhaust systems, and the old school practice of dropping compression with oversized head gaskets. All covered with actual shop floor experience, not just YouTube theory. The big theme of this episode? Right-sizing your build for your actual goals. Whether you're towing, pulling, or just want a badass street diesel, matching your parts to your power level makes or breaks the whole thing. If you've ever had buyer's remorse on a diesel truck build or you want to avoid it, this one's for you. | |||
| More Boost Does NOT Mean More Horsepower | 10 févr. 2026 | 01:00:35 | |
Everybody loves boost. The higher that gauge climbs, the better, right? Well, not exactly. This week on the Power Driven Podcast, Will and the guys get into one of the most argued topics in diesel performance. Boost. What it actually means, why more of it doesn't always equal more power, and where the whole "boost is just a measurement of restriction" idea even came from. The conversation started after a buddy rolled in from Washington with a 6.0 Power Stroke on one of their new 68mm GT turbos. The thing laid down 662 horsepower to the wheels on completely stock heads and a stock intake. At only 33 pounds of boost. Meanwhile builds running 45 to 50 pounds are struggling to match that number. So what gives? Turns out the number on your boost gauge is only part of the story. What's happening on the exhaust side, how well your cylinder heads flow, your intercooler efficiency, air density, exhaust back pressure, all of it plays into how much power actually makes it to the tire. The guys break all of that down in a way that actually makes sense whether you're building a diesel drag truck, a tow rig, or just trying to get more out of your daily driver. They also get into why diesel turbo technology has quietly lapped the gas performance world, the real reason gasoline engines can make insane power at lower boost, and the tuning strategy behind the Junker's 1,170 horsepower 12 valve build. Plus the age old turbo sizing debate, why chasing peak dyno numbers can actually ruin a truck, and why the best feeling diesel you've ever driven probably wasn't the highest horsepower one. You don't feel a horsepower number. You feel fun. If you want to go deeper on diesel performance, turbo theory, and real world builds, subscribe to the Power Driven Podcast and leave us a review. It helps more diesel guys find the show and keeps the conversation going. | |||
| You DON'T Need a $6,000 Cylinder Head.. | 03 févr. 2026 | 00:57:46 | |
Ever wonder if cylinder heads actually matter on your diesel truck, or if it's all just turbo talk? In this episode of the Power Jam Podcast, we're diving deep into the world of cylinder head performance after picking up a massive 73 horsepower on our short bed 12 valve Cummins with our stage two street performance head. For years, diesel guys have been told that boost solves everything. Got a restrictive head? Just add more boost and call it good. We're here to bust that myth wide open and explain why your engine actually cares about head flow, even when you're running a turbo. Whether you're driving a 12 valve, 24 valve, or common rail Cummins, understanding how air actually moves through your engine is the key to unlocking real power. We break down complex concepts like pressure differential, coefficient of discharge, and port velocity in ways that actually make sense. No engineering degree required. You'll learn why bigger valves aren't always better, why some expensive ported heads actually perform worse than stock, and how something as small as a valve job can make or break your entire build. This isn't just theory either. We talk real world results from trucks like Vendee, which is making 739 horsepower on a single turbo while staying remarkably clean. We discuss the differences between tow heads, street heads, and race heads, and help you understand which option makes sense for your application and budget. Whether you're building a dedicated sled puller, a reliable tow rig, or a street truck that needs to last, we cover everything from intake shelf modifications to induction hardened seats. We even tackle common questions about dimpled ports, oversize valves, and why some performance heads fail sooner than others. If you've ever wanted to understand what really happens inside your diesel engine and how to make smart decisions about cylinder head upgrades, this episode is for you. We keep it real, keep it practical, and give you the knowledge to make your truck perform better without wasting money on parts that don't deliver. | |||
| We Tested Water Meth on 10+ Trucks: Here's What Happened | 27 janv. 2026 | 00:48:40 | |
Welcome to the Power Driven Podcast from Power Driven Diesel. In this episode, we're answering a listener question from SuperCalFragilisticExpialidocious7314 about different power adding systems for diesel trucks. We start by talking about our experiences with water injection and water methanol injection on multiple builds. Spoiler alert: water injection lost power on almost every truck we tested, from single turbo street trucks to triple turbo race setups. There was only one time it actually picked up power, and we'll explain exactly why that happened and what made it different. Then we get into methanol injection and why it can actually add real horsepower on certain trucks, especially those with fuel system limitations like VP44 pumps. We've seen methanol add anywhere from 40 to 100 horsepower depending on the setup, and we explain the science behind why it works, when it helps with EGT control, and when it doesn't. We also touch on propane injection, nitro methane testing we did on one of our old trucks, and why compound turbo setups sometimes respond differently to methanol than single turbos. The second half of the episode covers superchargers versus turbochargers on diesels. If you've ever wondered why superchargers are popular on gas engines but almost nonexistent in the diesel world, we break down the real reasons. We talk about parasitic loss, why diesels need way more boost than gas engines, and why that creates huge problems for superchargers trying to keep up. We also discuss some real world examples of builders who tried supercharger only setups and supercharger turbo compounds, including results from guys like Brad Ponzi and Crazy Carl's Turbos. The results might surprise you, but we explain exactly why turbos keep winning in the diesel performance world. If you've got questions about water meth, boost systems, or anything diesel performance related, drop them in the comments. We read every one, and yours might end up as a full episode topic. | |||
| 2800°F EGT showed up and here’s what actually melts.. | 20 janv. 2026 | 00:54:45 | |
2800 degrees does matter. That will melt everything after the engine.” We kick this one off with a real story about a pegged EGT gauge and use it to crack open what exhaust gas temperature actually tells you and why placement matters. We explain EGT in plain terms and dig into the difference between reading pre turbo and post turbo, including the ballpark rule one of us saw when testing that showed roughly 100 degrees per 10 pounds of drive. Most light duty diesel folks read pre turbo, so the rest of the conversation stays there. From there we poke at the old 1250 safe myth and talk about why newer common rail trucks can see 1350 to 1400 on a hard pull while a 12 valve might not love that long term. Timing plays a huge role and we lay out how advancing timing can drop the EGT number while raising the actual heat the piston sees. That’s why a lower number isn’t always safer. We walk through the failures we’ve actually seen in the shop and at the track like melted turbine wheels and dividers when the hot side is the weak link versus pistons that scuff from heat and clearance. We also share a simple towing habit that helps, which is watching coolant as a proxy for oil temperature and backing off after a big climb instead of idling hot. If you’re fighting high EGT while towing we talk through fixes that work in the real world. The big one is getting the right turbo for your RPM and load because a mid sized single makes a truck smoky and hot. Freeing up the exhaust after the turbo helps drive pressure and spool. An upgraded intercooler can drop intake temps and we’ve seen that turn into a noticeable EGT reduction. Cylinder head flow and a sensible cam improve volumetric efficiency so the same fuel makes more power with less heat. We even get into water and water meth injection and where it can make sense. We wrap it with how we’d spend money on a tow build with tuning first then turbo then fuel and why that order worked on our own tow rig. If you care about towing, turbos, timing, common rail versus 12 valve behavior and real diesel performance, this episode is for you. | |||
| Can a Diesel Pickup Really Get 30 MPG?? | 13 janv. 2026 | 01:01:25 | |
Fuel mileage is one of those things everybody talks about, but when you start digging into it, you realize it is not just one magic mod. In this episode of the Power Driven podcast, the guys get into what actually moves the needle on diesel pickup fuel economy and why some trucks can pull off numbers like 30 miles per gallon when most people assume that is impossible. It kicks off with a FreedomWorks video where a built 12 valve Cummins shocks everybody by cracking over 30 mpg in a baseline run, and that launches the whole conversation. They talk about how that truck was not stock, it had things like timing bumped, bigger turbo setup, four inch exhaust, and it was a two wheel drive, which matters more than people want to admit. From there they get real about the biggest easy win, getting rid of waste, and a lot of that starts with how fast you are driving. Dropping speed to keep rpm down and cut wind drag can be the difference between a normal 16 to 17 mpg truck and something that starts creeping into the low 20s. Then they spend serious time on tires because the difference is not small. They explain why skinny tall tires like a 235 85 16 can help drop cruising rpm and rolling resistance, and they compare that to what happens when you go bigger and more aggressive. They also get into the reality of injectors and timing, and why more timing is basically step one across platforms, whether you are talking 12 valve, 6.0 Power Stroke, or common rail. They break down timing in plain terms, why emissions pushes timing in a certain direction, and how tuning decisions like timing split can make a truck efficient without being risky when you are just cruising. From there it rolls into airflow and turbo choices, why turbine side matters so much for efficiency, and how transmission lockup, rail pressure, and even smoke all tie back into fuel economy. The whole thing feels like a shop conversation that connects the dots between diesel performance parts and real world miles per gallon without pretending there is one simple answer. | |||
| Is 2026 the Best Time to Start Diesel Drag Racing? | 06 janv. 2026 | 01:21:42 | |
Diesel drag racing is officially back, and 2026 is shaping up to be a turning point for the sport. With new ownership, renewed momentum, and real effort being put into growing diesel motorsports nationwide, this episode of the Power Jam Podcast breaks down why now is the time to get involved and how anyone with a diesel-powered vehicle can jump in without it being intimidating. In this episode, the guys talk through what the changes in diesel racing actually mean for everyday enthusiasts, from the resurgence of organized events to the excitement around unified rules and growing participation. They reflect on how diesel drag racing exploded in the early 2000s, why it slowed down over the years, and why the conditions are finally right for it to grow again. The focus isn’t just on watching from the stands, but on encouraging more people to bring their trucks to the track and experience it firsthand. A big portion of the conversation walks through exactly how to get started racing, especially in the Sportsman class. They explain why you don’t need a fast truck, a massive budget, or race-only equipment to participate, and how consistency and reaction time matter more than horsepower. From tech inspection and staging lanes to understanding the tree, reaction times, and time slips, the episode removes the mystery around drag racing and makes it approachable for first-time racers. The discussion also covers how bracket racing works, how dial-ins and reaction times decide races, and why slower classes are often the most competitive and fun. As the episode progresses, they touch on moving up into faster classes, what changes as speed increases, and why learning the fundamentals in Sportsman sets you up for long-term success. If you’ve ever thought about racing your diesel truck but didn’t know where to start, this episode lays it out in real-world terms. It’s about growing the sport, helping new racers feel welcome, and keeping diesel motorsports alive by getting more trucks on the track. | |||
| What 2025 Taught Us About Making Diesel Power | 30 déc. 2025 | 01:04:50 | |
We learned some things in 2025 that completely reshaped how we think about diesel performance, and a lot of it challenged what most people assume about power, smoke, and tuning. This episode of the Power Driven Podcast is a year end breakdown featuring the Power Driven Diesel crew reflecting on everything they tested, broke, and learned throughout the year. The conversation covers diesel performance across multiple platforms including 12 valve Cummins, common rail Cummins, and VP44 setups, along with what real dyno testing and track time revealed. From R&D and turbo testing to race truck builds and tow rigs, this episode explains why small details in air, fuel, and timing matter more than chasing parts alone. One of the biggest topics is smoke versus power and why adding fuel does not always mean more performance. They dig into the question of whether smoke adds power on a diesel and explain how different platforms respond, especially comparing older 12 valve technology to modern common rail engines. The discussion naturally leads into AFR tuning, running lean versus rich, and how nitrous diesel tuning completely changes the equation when it comes to heat, burn efficiency, and timing. There’s a deep look at nitrous on diesel engines, including why pulling timing with nitrous is critical, how automated nitrous control improves consistency in diesel drag racing, and why feed line size and solenoid flow actually matter. Turbo upgrades and truck builds are another major focus. The crew breaks down real dyno results from turbo testing on different trucks, including the Junker drag truck, Windy, and Willard. They talk through GT55 and Aggressor turbo results, injector sizing lessons, and how some setups made more power than expected without bending factory rods. There’s also insight into wastegate testing, comparing screamer gate versus hot pipe gate setups on compound turbos. The episode wraps with lessons on VP44 Cummins performance, towing capability, camshaft upgrades, cylinder head flow testing, and why there’s still a lot of untapped potential in Cummins head design. Subscribe for more Power Driven Podcast episodes, follow along for more diesel performance testing, and check out everything Power Driven Diesel is building next. | |||
| We Had to Pick Just 3 Tow Truck Upgrades… Here’s What Won | 23 déc. 2025 | 00:47:16 | |
If you had to pick just three upgrades to make your tow truck better, what would they be? In this episode of the Power Driven Podcast, Will, Todd, and Meyers break down their own personal tow trucks and go head to head choosing their top three favorite upgrades. They turn it into a white-elephant style game where once a mod is picked, nobody else can use it, forcing each guy to really think about what has made the biggest difference in how their trucks tow, drive, and survive long miles. This conversation hits home for diesel enthusiasts because it focuses on real world diesel performance, not bench racing or internet theory. The episode kicks off with tuning as a must-have upgrade and why controlling fuel, power delivery, and transmission behavior is step one for any modern Cummins tow rig. They explain how multiple EFI Live tunes allow different transmission pressure strategies for towing versus street driving, and why constant high line pressure is a fast way to create unnecessary heat and wear. From there, turbo upgrades come into play, including variable geometry turbos with billet actuators and how a stronger, more consistent exhaust brake can completely change downhill control and driver confidence. As the picks continue, the conversation moves into built transmissions with second gear lockup, lower stall torque converters, and why factory shift strategies fall apart once you add power. They also dig into suspension upgrades like airbags and onboard air systems, explaining how leveling the truck and controlling tongue weight makes towing safer and more predictable. Exhaust brakes, rear sway bars, headlights, brakes, shocks, and tires all come up as critical upgrades that reduce stress when towing heavy through wind, traffic, mountains, and backroads. Over the course of the episode, the conversation naturally bounces between real world diesel performance, Cummins tow rigs, tuning strategies, turbo setups, and what actually makes a truck nicer to live with when you’re towing heavy. It’s the kind of discussion that comes from years of hauling trailers, breaking parts, fixing mistakes, and figuring out what upgrades actually make a difference. | |||
| What It Really Takes to Make Reliable High Horsepower Diesels | 16 déc. 2025 | 01:01:39 | |
This one turns into a battle royale fast, with Myer and John wasting no time getting into a heated shop floor debate about extreme diesel performance and what really works when you are pushing the limits. The conversation dives straight into drag racing setups, large single turbo strategy, and the tuning challenges that show up when you are chasing real, repeatable power. A major focus is why mechanical injection setups often seem to extract more out of big single turbos compared to common rail, especially when dyno testing at higher elevation. For diesel enthusiasts who actually build, tune, and race their trucks, this matters because it directly affects spool, drivability, consistency, and whether a setup survives repeated passes or starts melting parts. One of the key discussions centers around a fuel only goal of 1,500 horsepower on a 6.7 Cummins running a 98mm GT55 style turbo. They break down how the dyno testing process worked by starting with low fuel quantity and timing, then gradually stepping things up until timing stopped making gains and fuel became the deciding factor. Myer explains why pushing past that range started to hurt the truck’s manners and why nitrous became the tool for setting peak power while keeping the truck responsive and controllable instead of lazy and unpredictable. They go deeper into why large single turbos struggle more at altitude, particularly on common rail trucks that burn fuel so efficiently in cylinder that there is not enough heat left to drive the turbine. The discussion covers attempts to tune around that limitation, including lowering rail pressure to mimic a more 12 valve style burn, the dangers of overfueling a big single, and why once the setup falls off there is often no saving it mid pull. They also talk through future plans like switching to a ten bar map sensor, experimenting with pressure and timing, and trying to find the balance between clean combustion and enough exhaust energy to keep the turbo lit. Real world shop experience is layered throughout the episode, including nitrous strategy for drag racing, why compound setups can feel more foolproof even with the added weight, and a nitrous backfire that blew an intake pipe off and dented a hood during testing. If you are into diesel performance, Power Driven Diesel shop talk, Cummins builds, VP44 discussions, dyno testing, turbo upgrades, drag racing, and truck builds, this episode delivers straight insight from guys who live it. Subscribe for more episodes and stay locked in with everything happening at Power Driven Diesel. | |||
| Build A 1000HP 12V Cummins That Actually Drives | 09 déc. 2025 | 01:01:34 | |
We break down how to build a clean street friendly 1000 horsepower 12 valve Cummins without the smoke show or sketchy manners. This Power Driven Podcast features Meyer with guest John Schroeder from Black Tie Race Fab, and the crew gets real about what it takes to cross four digits while keeping a truck fun in town, on the dyno, and at the strip. Instead of throwing the biggest parts at a 12 valve, they walk through the combination that actually works in diesel performance, from engine foundation and timing to turbo sizing, compound setups, fuel supply, and boost control. The first myth they crush is the idea that a giant 13 millimeter pump and huge injectors are mandatory. A well planned 12 millimeter with a 215 pump’s timing advance often makes more usable power with better manners. Too little timing creates what they call phantom boost because the burn finishes in the manifold, not the cylinder. Add sensible timing and boost can drop while power climbs because the work happens in the chamber where it belongs. On the hard parts, rods and rod bolts are smart for a torquey street combo, and the Junker’s proven recipe shows what survives at this level with piston to wall around ten to eleven thousandths and a wider top ring gap. Up top, a ported head with fire rings keeps power up and intercooler boots alive when boost hits triple digits, and quality valve springs with a moderate cam keep rpm happy without turning the truck into a picky race piece. Turbo sizing is where street trucks win. Oversized fuel with lazy air equals smoke and frustration. The team explains how a small responsive manifold charger like a 62 paired with a large atmosphere charger such as an Aggressor 98 on a GT55 lights early, pulls hard, and still delivers four digit results. Wastegate control can swing total boost from roughly the mid one hundreds down near one hundred without always adding power, which proves that airflow quality beats a big number on the gauge. Fuel supply is its own power adder on a P pump. You need volume to flush aeration between injection events, whether that is a strong mechanical lift pump or a smart boost referenced electric. An adjustable pump gear is cheap insurance against slipped timing and makes fine tuning fast and repeatable. If you care about Cummins tuning, dyno testing, turbo upgrades, drag racing, and real world truck builds, this episode delivers with takeaways like compound turbo street setup, 215 pump timing advance, lift pump volume for a P pump, and a ported 12 valve head with fire rings. Subscribe for more and follow Power Driven Diesel for the builds, parts, and testing that make these trucks fast and fun. | |||
| What Comes Next For Diesel Drag Racing?? | 02 déc. 2025 | 01:08:36 | |
One spec turbo, instant green starts, and a purse swelling toward one hundred grand turned this class into the wildest storyline in diesel drag racing. This episode of the Power Driven Podcast is hosted by Will and jumps straight into the future of diesel motorsports with Josh and Myers in the room. The crew uses the 72 Fast class that runs alongside UCC in Indianapolis as the case study for where the sport is heading and why it matters to anyone who cares about diesel performance and the community that builds, tows, tests, and races these trucks. They lay out the rules that make this thing so fierce. Every entry runs a VS Racing seventy two eighty T4 turbo and must weigh a strict six thousand pounds with no tolerance. It is fuel only, so no nitrous, no injectables, and no water to air intercoolers except where a factory six seven Power Stroke came with one. Factory pumps are required, a factory ECM is mandatory even if you swap brands, and there is no trans brake. There is a parc ferme style impound between rounds, no test passes in the days before the event, and an instant green start on race day. The entry options even included a package with the turbo, the purse began at fifty thousand, contingencies piled on, and the total payout grew toward one hundred thousand as the entry list capped at one hundred thirty five. From there it gets technical in all the right ways. The guys explain why common rail tuning windows and cylinder head airflow are a real edge over a twelve valve, how port velocity and reversion affect turbo efficiency, and why a P pump setup benefits from a larger turbine to deal with heat and drive pressure. Expect everything from eight or nine hundred horsepower to well past a thousand, and on an eighth mile you could see anything from six eighties to possible high fives depending on weight, power, and the leave. With foot brake only and an instant green tree, reaction time and a clean launch can beat raw power, which is exactly why this format pulls in racers from street truck roots to serious shop builds. Culture and logistics get their due as well. Burnout pits are drawing bigger crowds because fans can stand close and feel the noise and smoke, which makes them a real part of the show. There is talk of bringing an air limited, fuel only class out West, maybe pairing it with dirt drags or a street weight sled pull so the barrier to entry stays low. The no time format keeps scoreboards dark, but the tower still sees times and track officials have the final say, a reminder that safety, licenses, and sportsmanship still matter when serious money is on the line. Contingency bounties add even more spice, including brand versus brand bonuses when one platform sends another home. If you live for diesel performance, Power Driven Diesel tech, Cummins talk, VP44 history, dyno testing, turbo upgrades, drag racing, and truck builds, this conversation is packed with shop floor reality and race day strategy. Long tail topics woven throughout include 72 Fast class rules at UCC, VS Racing seventy two eighty spec turbo details, six thousand pound minimum weight, factory ECM only with no trans brake, instant green fuel only diesel drag racing, no test pass rule with impound, and eighth mile strategy on a budget. Subscribe, drop your take in the comments, and follow Power Driven Diesel for more episodes that keep you in the lanes and in the shop. | |||
| Back to the Basics of Diesel Power | 25 nov. 2025 | 00:59:28 | |
Diesel really is king when it comes to doing real work, and in this episode of the Power Driven Podcast the crew slows things down and explains why in plain language. The whole conversation kicks off because a viewer told them they were talking over his head, even though he is a car guy, so they decided to go back to basics, talk in a way everyone can follow, and break down why they love diesels, why they are better for work, and where all the old misconceptions came from. They start by going back to the nineteen seventies oil embargo, when fuel prices spiked and Oldsmobile rushed out those early diesel car engines that were basically gas designs turned into diesels. Those things were slow, unreliable, non turbo junk, and that is where the idea that diesels are noisy, smoky turds really stuck. From there they walk through why modern diesel performance is a completely different world. Higher compression ratios, no throttle blade to choke airflow, and a huge usable air fuel ratio range all add up to better efficiency and better fuel mileage. They talk real numbers on air fuel ratio for gas versus diesel, explain pumping losses, and compare BTUs in diesel and gasoline so you understand why ships, trains, and semis all run on heavy fuel and diesel instead of gas. The episode then moves into torque, dyno behavior, and how turbos change everything. The guys explain why a diesel can live all day in that sixteen hundred to twenty six hundred rpm power band and still pull hard, while a gasoline tow rig has to scream and constantly downshift to make the same horsepower. They dig into how turbochargers effectively multiply engine size, why compound turbos on a Cummins let you add air, run leaner, and pick up big power on the dyno without adding more fuel, and how that shows up on the road when you are towing a trailer up a grade. There are real towing stories about EcoBoost and half ton gas trucks struggling with plugged converters and heat, compared to turbo diesels that just chug along and even get more efficient as you add load. They also touch on modern emissions systems, cold running exhaust, short trip driving, and why older seventies diesels feel weak while newer pickup and semi truck engines are built robust with heavy rods, pistons, and high pressure fuel systems that make serious diesel performance possible. If you are into Power Driven Diesel tech talk, Cummins trucks, dyno testing, turbo upgrades, drag racing with tow rigs, or just want a clear diesel vs gas towing and fuel economy explanation, this back to basics episode is a solid listen. Subscribe for more Power Driven Podcast episodes, follow along for more diesel performance content, and keep up with the latest truck builds, towing tests, and shop stories from Power Driven Diesel. | |||
| Scrat Is Going to UCC 2026: Second Gen Dodge Build Plan | 18 nov. 2025 | 00:56:03 | |
Scrat, a 1996 second gen Dodge, is headed to the Ultimate Callout Challenge 2026 with Myer at the wheel, and the plan is simple. Build it in the shop, keep it serviceable, and make it live through the dyno, the drag strip, and the sled pull. This episode of the Power Driven Podcast features Will and Todd with Myer talking through the UCC plan, why it matters to diesel fans, and how it stacks up against King of the Streets. The focus is on real shop work, quick turnarounds, and a strategy that favors reliability without taking the fun out of pushing hard. Scrat is getting a back half and four link while keeping a steel cab and a straightforward layout. The goal is to be around four thousand six hundred pounds with driver, chase a five forty in the eighth mile, and make a strong dyno number with a clean nitrous plan. Tuning talk stays practical, from common rail control to the debate between an 06 to 07 Bosch 849 and a Bosch motorsport standalone, with Haltech pieces already in play. Transmission work is front and center as well, taking lessons from Josh and The Godfather into a forty eight based setup aimed at holding power without slipping. The conversation hits safety and prep too, from blown tire lessons on the chassis dyno to smarter safeguards that do not get in the way of a good pull. Competition looks stout with names like Lenny Reid in the mix, which is exactly the kind of field that makes UCC worth the grind. Testing in Vegas, engine work in house, and steady progress updates will lead up to the first week of June 2026. If diesel performance, Cummins power, dyno testing, turbo upgrades, drag racing, and real truck builds are your thing, subscribe to the channel, follow the Power Driven Podcast, and keep up with Power Driven Diesel as Myer gets Scrat ready for the Ultimate Callout Challenge. | |||